Author Archives: Prime Alliance Marketing - Page 16

Presto Lifts: Understanding AGM (Absorbed Glass Mat) Batteries

Posted by on March 28, 2014 Comments Off on Presto Lifts: Understanding AGM (Absorbed Glass Mat) Batteries

AGM style batteries are standard on many of Presto Lifts standard products*. These state-of-the-art, deep cycle, lead acid batteries provide a number of benefits.

  • Sealed, Safe and Maintenance-Free: No need to add electrolyte and will not emit gasses during normal recharging. Even if ruptured there is nothing to spill.
  • Low Self Discharge Rate: The battery will remain fully charged for many months before charging is required.
  • Deep Discharge Recovery: Advanced design and composition have greatly improved the batteries ability to recover from excessively deep discharge.
  • Easy Handling: No special handling precautions. AGM batteries are classified as a non-hazardous commodity.
  • High Discharge Rate: Low internal resistance allows discharge currents of up to ten times the rated capacity of the battery.
  • Rugged Construction: The high impact resistance battery cases are made either of non-conductive ABS plastic, polypropylene or styrene. All of these case materials impart great resistance to schlock, vibration, chemicals and heat.
  • Long Service Life: Under normal operating conditions, four or five years dependable service life can be expected in stand-by applications, or between 200-1000 charge/discharge cycles depending on average depth of discharge.

AGM batteries may be discharged over a temperature range of -40 degrees Fahrenheit to +140 degrees Fahrenheit.

 

New From Presto Lifts: P3PH Powered Pallet Positioner

Posted by on March 28, 2014 Comments Off on New From Presto Lifts: P3PH Powered Pallet Positioner

Powered P3PH Powered Pallet PositionerThis operator controlled Presto P3PH-24 fills the need where loads, weights and pallet sizes are not consistent. Using a foot controller, the operator can adjust the pallet height from 8 3/4″ to 33 1/2″ for ergonomic comfort. Like the P3-AA the P3PH-24 features a 43″ diameter ring style turntable, foot control, 6″ x 2″ fork pockets and can be relocated with a fork truck. Power required is 115v single phase. Available in 2,000 and 4,000lb capacity.

Presto Lifts, Understanding NEMA Standards

Posted by on March 26, 2014 Comments Off on Presto Lifts, Understanding NEMA Standards

Here is a little information that Presto Lifts thought would be helpful in understanding NEMA standards.

When equipment is going to be exposed to water special consideration has to be given to the electrical system. The National Electrical Manufacturers’ Association (NEMA) is the US organization that has set protection standards for electrical enclosures and is the equivalent to European IP ratings. An enclosure is a surrounding case constructed to provide a degree of protection to personnel against incidental contact with the enclosed equipment (i.e. transformer, motor starter, relay and pushbutton contacts) and to provide a degree of protection to the enclosed equipment against specific environmental conditions. The following is a brief description of each NEMA type enclosure. NEMA types 1,4 and 12 are the most common types of enclosures used with the Presto Lifts equipment.

  • NEMA 1 GENERAL PURPOSE: These enclosures are suitable for general purpose applications indoors where atmospheric conditions are normal. These enclosures are primarily used to prevent accidental contact of personnel with the enclosed equipment. They also serve as protection against falling dust, but are not dust tight.
  • NEMA 4 WATER TIGHT/DUST TIGHT: These enclosures are intended for indoor or outdoor use to provide protection against windblown dust and rain, splashing water, and hose directed water from any angle, however, they are not submersible. They are suitable for application in dairies, breweries, etc. (WATER WASH DOWN)
  • NEMA 12 DUST TIGHT/DRIP TIGHT: Industrial enclosures intended for use indoors to provide protection against fibers, fillings, lint, dust, dirt, seepage, dripping and external condensation of noncorrosive liquids.

Pallet vs Skid?

Posted by on March 26, 2014 Comments Off on Pallet vs Skid?

Pallet vs Skid, are they trying to lift a Pallet or a Skid? This is still the most common question asked in the Presto Lifts office.

There are two main types of pallet designs: block and stringer. Stringer type pallets are more common. Stringer pallets only allow pallet jacks or forklifts to enter on the ends; they are called 2-way. If the stringers are notched (like a GMA pallet) a fork lift (not a pallet jack) can enter on the sides; this is a partial 4-way.The principle advantage of the block pallet is pallet jacks and forklifts can enter from any side; this is a true 4-way pallet. Skids are open bottom pallets. They are generally less expensive to manufacture and are typically not as durable as a pallet because the stringer is unsupported on the bottom and is more susceptible to damage. Skids are common in certain industries like printing and graphics.

Presto Lifts Modified Lift and Tilt Table

Posted by on March 26, 2014 Comments Off on Presto Lifts Modified Lift and Tilt Table

The dealer was looking for a lift and tilt table with 1500 lbs of capacity, 96″L x 36″D tilt platform, tilting to 30 degrees, to be used in a clean room. Presto Lifts was able to offer a model XLD36-40/WT30-20, with 2000 lbs capacity, 30 degrees of  tilt, 48″W x 84″L lift platform, 42″W x 96″L tilt platform, bellow skirting, food grade hydraulic fluid, and a drip pan for the lift and tilt.

New England Company Installing Three Cogan Mezzanines to Compliment the Two They Already Have.

Posted by on February 23, 2014 Comments Off on New England Company Installing Three Cogan Mezzanines to Compliment the Two They Already Have.

This  post is a before snap shot of a companies warehouse just north of Boston who will be installing 3 more Cogan Mezzanines to increase their storage and processing capacity. This company has already installed 2 Cogan Mezzanines and multiple rows of Cogan Cantilever Rack.

This is the first area. 

This is the second area. 

This is the third area. 

Latest Cogan Installation of VNA Cantilever Rack in New England

Posted by on February 23, 2014 Comments Off on Latest Cogan Installation of VNA Cantilever Rack in New England

Here’s a photo gallery of the latest installation of a Cogan Cantilever Rack system being used in an automatic door manufacturers’ facility in central CT. The manufacturer was utilizing an outdoor location to store their material and built an addition to their plant to move the stock indoors. The system was designed using the Very Narrow Aisle (VNA) concept. Standard Cogan Cantilever Rack is used with the addition of floor angle to guide the Side Loading Forklift through the aisles. This job was expertly designed and sold by Warner Specialty Products of North Haven, CT.

 

Cogan Guardrail Application Ideas

Posted by on December 8, 2013 Comments Off on Cogan Guardrail Application Ideas

Some job site photo’s showing application ideas for Cogan Guarding products.

Cogan Mezzanine Before and After

Posted by on October 29, 2013 Comments Off on Cogan Mezzanine Before and After

Here are two shots that show the added storage space that a Cogan Mezzanine can provide.

What Presto Lifts Needs to Know to Quote the Right Machine

Posted by on October 9, 2013 Comments Off on What Presto Lifts Needs to Know to Quote the Right Machine

Presto LiftsIt can be difficult to gather all the information needed to get a proper quote. Going back and forth with an end user to get more information can be time consuming and certainly doesn’t portray the image we all strive for as professional salesmen. Here’s a quick run down on the information Presto Lifts will need to generate an accurate quote the first time.

  • What’s the sequence of operation
  • Capacity
  • Lowered height
  • Raised height
  • Size of the load
  • How is it being loaded
  • How is it being off loaded
  • Air or hydraulic
  • Manual or powered
  • If multiple units, do they want them all delivered at one time
  • What’s the time frame for the order
  • Photos or Drawings of the application if available

Understandably, you may not be able to gather all this information, but if available, will make the quoting process quicker and more accurate.

Prime Alliance Marketing is a full service Material Handling Rep Agency dedicated to promoting the lines we represent and to helping our dealer base be more successful selling them.